Soakaways are an old-fashioned way of disposing of surface water generated by buildings. However, they need to comply with building regulations in order to be legally installed. Specifically, they need an Environment Agency Permit and must be installed at least five meters from a boundary or building.
Soakaways are a traditional way of disposing of surface water from buildings
Soakaways have long been used as a means of disposing of storm water. They are especially beneficial in fully sewered urban areas because they allow new building works to be scaled back without impacting existing sewers, and they also avoid the cost of sewer upgrading outside the development. Soakaways are now seen as a more widely applicable solution, and their benefits are not limited to reducing the amount of surface water that is discharged.
Soakaways are relatively simple to construct. The materials required are inexpensive and widely available. Gravel can be purchased at most builders’ merchants. A 20m long, flint-grained granular gravel is ideal. Drainage pipes are then installed, carrying water to the soakaway. Over time, soil will build up and clog the soakaway, but heavy-duty fabric can prevent this from happening.
They require an Environment Agency Permit
If you plan to run a soakaway, it’s important to make sure you have the proper permit before you can start operating your business. This document specifies the rules that you have to follow, and will also tell you what you can and cannot do. The Environment Agency can decide to refuse your application if you don’t meet the requirements for operating your business. To avoid this situation, you can make joint applications with other operators. These joint applications are typically for the same treatment plant.
In order to be approved, a soakaway drain must be installed in an aerobic soil layer. This means that it must be built at least seven meters from any habitable part of the property. In addition, it must be placed at least 50 metres from a borehole. The Environment Agency will require you to apply for a permit before you can install a soakaway.
They must be installed at least five metres from a building
In order to avoid causing damage to the foundations of a building, soakaways should be installed at least five metres from it. This applies to domestic soakaways as well as to larger infiltration systems. However, it is possible to install a soakaway at a closer distance if necessary. For this, you can use perforated pipes, soakaway trenches, or soakaway pits. If you are unsure, contact the sewers for Adoption, who can give you advice.
A soakaway is a unique drainage system that is designed to deal with surface water in the area where it occurs. Unlike traditional methods, this method does not use chemicals to treat the water before it is returned to the environment. It also reduces the pollution caused by surface water.
They must be at least two and a half metres from a boundary
A soakaway is a drainage system that collects rainwater. It should be located at least two and a half metres from a boundary. It must comply with building regulations and be approved by building control. Failing to meet the regulations could lead to fines and you may have to rectify your property. Be aware that some companies issue non-compliant certificates, so make sure you follow the rules and regulations carefully.
Soakaways must be at least two and half metres from a boundary, and should be placed on stable ground. You should also ensure that the soil is at least 300mm deep. It should also be able to soak up water for at least 10 minutes. The soil should also be able to be replenished up to 10 times. Otherwise, it is not suitable for use as a soakaway.
They must be constructed with plastic crates
A soakaway is a system that collects rainwater from a house and stores it in a void under the ground. Its purpose is to collect water from your home’s roof, driveway, and garden. Soakaways are not to be confused with “foul water soakaways”, which are designed to collect the same water but are used for different purposes. Plastic crates are the best material for building a soakaway, as they’re strong enough to last decades.
Soakaways come in various sizes, with the most common being a one cubic metre capacity. They are available in two main classes: garden soakaways and driveway soakaways. The most suitable location for a soakaway is a low, flat area away from the building, preferably below it.
Click here to learn more about drain repair company